Sheet updated September 2026
The Duotone Monobloc Tail H D/LAB 2027 is your ultimate stabilizer for extended glide and downwind. It also excels at parawing. This single-piece tail and stabilizer features a 9.3 aspect ratio and a secure 3BS+ connection with an additional fourth screw. It's engineered specifically for the Glide 3.0, Hyperglide, and Amp 2.0. Choose from two sizes: 130 cm² and 150 cm².
KEY INFORMATION
DUOTONE MONOBLOC TAIL H D/LAB 2027 - Glide-Oriented Foil Stabilizer
What we like
- Monobloc construction: The tail and stabilizer are one piece, reducing drag and delivering direct response.
- 9.3 aspect ratio: This thin stabilizer minimizes drag and extends your glide.
- Designed for the Glide range: Duotone developed this stabilizer with the Glide 3.0, Hyperglide, and Amp 2.0.
- Optimized for pumping: Connect to swell and maintain flight even in light conditions.
- Directional stability: This stabilizer holds its course, which is invaluable for downwind and freefly.
- 3BS+ connection: The fourth screw locks in the pitch for ultimate control.
- Two sizes: The 130 cm² comes with a 43 cm tail, while the 150 cm² features a 40 cm tail.
Use
Downwind • Parawing • Freefly wing foil
Available sizes
Color
Carbon
Included / Not included
✓ Included: Monobloc stabilizer, screw set
✗ Not included: Front Wing, Fuselage, Mast
DETAILED DESCRIPTION
A Stabilizer That Prioritizes Glide
The Monobloc Tail H has a clear focus: it prioritizes glide and directional stability over playfulness or pure speed. Duotone designed it for downwind and parawing, with freefly wing foil riders in mind. Compared to a turn-oriented stabilizer, it offers less responsiveness but significantly more efficiency and calm.
The Monobloc Construction
The tail and stabilizer are crafted as a single piece, eliminating any joints. This removes an interface, which means no source of drag or parasitic flex. Power transmission becomes direct, and the response is sharper. It's the same principle as with a Front Wing: the fewer parts between your foot and the water, the clearer the feedback.
A 9.3 Aspect Ratio
The stabilizer is long and thin. It features a 9.3 aspect ratio on both sizes. A high aspect ratio at the rear reduces induced drag and improves overall efficiency. This lets you stay in flight longer, connect with swells easily, and experience less fatigue during long downwind sessions.
Developed for the Glide Range
Duotone engineered this tail specifically for the Glide 3.0, Hyperglide, and Amp 2.0 wings. The harmony between the Front Wing and the stabilizer dictates the final behavior: a poorly matched stabilizer negates the benefits of a good wing. It also boosts pumping and glide performance for the Crest range.
The 3BS+ Connection
The 3BS+ system, with its fourth screw, maximizes pitch stability and control while maintaining direct and connected sensations. For a glide-oriented setup, where you want to avoid constant correction, the stiffness of the connection is as crucial as the geometry.
Choosing Between 130 and 150
Both sizes share the same 9.3 aspect ratio. The 130 cm² mounts on a 43 cm tail. This results in a 34.8 cm wingspan; the 150 cm² mounts on a 40 cm tail for a 37.4 cm wingspan. More surface area provides stability and lift at low speeds, while less surface area enhances handling. The attachment to the D/LAB Front Wing uses an M6 x 25 screw, tightened to 10 Nm, which is included in the screw set.
SIZE GUIDE
| Size | Surface | Wingspan | Tail length | Aspect Ratio | Construction |
|---|---|---|---|---|---|
| 43 / 130 | 130 cm² | 34.8 cm | 43 cm | 9.3 | D/LAB carbon monobloc |
| 40 / 150 | 150 cm² | 37.4 cm | 40 cm | 9.3 | D/LAB carbon monobloc |
VIDEO
TECHNICAL SPECIFICATIONS
| Specifications | |
|---|---|
| Type | This monobloc foil stabilizer is engineered for exceptional glide and downwind performance. |
| Construction | The D/LAB monobloc features a single-piece tail and stabilizer design. |
| Aspect Ratio | Both sizes boast an aspect ratio of 9.3. |
| Surfaces | 130 and 150 cm² |
| Tail lengths | The 130 cm² measures 43 cm, while the 150 cm² is 40 cm. |
| Wingspan | The 130 cm² measures 34.8 cm, and the 150 cm² is 37.4 cm. |
| Attachment | Use M6 x 25 screws to attach it to the D/LAB Front Wing, tightening to 10 Nm. |
| Connection | The 3BS+ system includes a fourth screw for added security. |
| Compatibility | This monobloc is compatible with Glide 3.0, Hyperglide, and Amp 2.0 Front Wings. |
| Screw set | Included |
| Season | 2027 |
FAQ - DUOTONE MONOBLOC TAIL H D/LAB 2027
This is for the downwind and parawing rider, as well as the freefly wing foiler, who wants to maintain flight and a stable course. This is not a tight-turning stabilizer; it is a performance stabilizer.
The 150 cm² provides more stability and lift at low speeds. This is useful for downwind and with large Front Wings. The 130 cm² frees up handling. Tell us which Front Wing you are mounting; it dictates the choice.
It is developed for the Glide 3.0, Hyperglide, and Amp 2.0. It also improves the pumping and glide of the Crest range. It mounts to a D/LAB Front Wing.
It's about the riding style. The H has an aspect ratio of 9.3. It's for glide and downwind. It's also for freefly. The F has an aspect ratio of 6.5, with a surface area of 165 cm² over 37 cm. It's for freestyle: pop, re-pop, and front foot pressure.
Benefit from the expert advice of our specialized team and comprehensive after-sales support.
▶ Need some advice?
GlissEvolution, 2c avenue du Gulfstream, 44380 Pornichet (Loire-Atlantique)
09 62 64 74 77 | WhatsApp: 07 83 28 39 94, Tuesday to Saturday, 10am-1pm / 3pm-7pm
Test center available by appointment
To go further
Customer reviews
Loading reviews...
Read more
Alternative Products
These other products might interest you
